Parts & Accessories

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.

Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).

Wheel Freehub Kit—XD Driver Body Kit—ZM1 3Zero - Compatible With: WH-MOTO-30-A1

Front RockShox/SRAM-specific Torque-Cap 15mm through-axle SealLock end caps for Neo and Neo Ultimate hubs. SealLock end caps feature a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. Torque-Cap end caps have the same 15mm inside diameter as other systems, but outside diameter is larger (31mm), making these end caps only compatible with Torque-Cap-compatible forks. Note: Torque caps are not compatible with centerlock hubs.

The mounting solution for thru-bolt front wheels. Designed for an axle diameter of 9mm in the front, the thru-bolt system is a special kind of axle mounting for bikes. The DT Swiss thru-bolt system is compatible with standard quick-release dropouts but requires hubs that are compatible with the Thru Bolt. The stronger wheel connection results in greater stiffness. - Overall Length: 115mm - Thread Pitch: M9 x 1.0mm - Flat Washer

Maximum stiffness and highest safety—the RWS Quick Release for road and MTB. Our patented RWS axle system is stiffer, safer, and easier to use than conventional quick-release axles. The RWS quick release is absolutely reliable and offers a strong connection to the frame. It's the perfect choice for anyone who is looking for maximum performance and safety.

Replacement axles for DT Swiss hubs.

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.

Bontrager Tubeless (TLR) Rim Tape creates an air-tight seal that covers spoke holes in the rim for easy tubeless tire setup and installation. The tape securely bonds to the rim and doesn't leave residue when removed. For use with wheels approved for TLR Tape-based tubeless conversion. - Provides durable, air-tight seal over spoke holes for tubeless conversion - Wrap four wheels with a single layer of tape or two wheels with a double layer - Provides secure adhesion to rim without leaving residue when removed - Thoroughly clean and dry rim bed before applying - For use with rims approved for TLR Tape-based tubeless conversion

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Sovos 9mm x 1, front hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag COMPATIBLE HUBS: - Sovos 9mm x 1, front hub - Taiwanese and similar front hubs with 9mm x 1 axle

The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button-head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - One-piece design - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6 mm hex wrench required for installation

The Deadbolt Thru-Axles feature the classic-looking Salsa lever and can be adjusted to return to the desired position when properly tightened. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

Keeping contamination out of your internally geared hub is critical to its function and longevity. Sometimes, the oil port bolt comes loose and it's easy to lose, even if you've just taken it out to oil your hub. Keep a spare or two so your hub stays clean inside and it'll last you many, many miles.

Need a Shift Cable Fixing Bolt Unit for your Alfine S7000/S700 hub? Here it is. Now, get that bike back on the road!

Shimano Dura-Ace 9000 Hub Quick Release Skewer. - Axle Type: Standard QR

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese front hubs - Type: Solid Axle - Threads: 9mm x 1 - Diameter: 9mm - Length: 155mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 155mm - 1 axle per bag

Simply replace the cones on your Supreme front and cassette hubs for a perfect fit without having to spread your dropouts. Available in front, rear, and drive side options. These guards now feature a heat-treated chromo insert for longer life.

Seal kit to keep water and dirt out of your Race Face Vault hubs.

Replacement freewheel spoke protector, in various sizes for different freehub sizes. - Made of clear plastic - Fits around standard freewheel threads